Skip to main content

Featured Post

Kerala's First 3D Printed Building

Created as a showcase project, AMAZE-28, the single-room summer house, was successfully constructed within 28 days on the grounds of the Kerala State Nirmithi Kendra. The 3D-printed building at the Kerala State Nirmithi Kendra in Thiruvananthapuram. (Photo: Shekunj)  The inauguration of Kerala's inaugural 3D-printed structure, a 380-square-foot single-room summer house, is scheduled to take place on October 10 at the Kerala State Nirmithi Kendra (Kesnik) campus located in PTP Nagar, Thiruvananthapuram.  Conceived as a showcase initiative, the summer house named AMAZE-28 was successfully finished within a mere 28 days. This impressive project was executed by Tvasta, a construction technology startup based in Chennai, founded by alumni of IIT-Madras, who have entered into a memorandum of understanding (MoU) with Kesnik.  AMAZE-28 is perched upon a concrete foundation atop a gentle elevation within the Kesnik campus. Febi Varghese, the Director and Chief Executive Officer of...
Post a Comment

Materials used in Additive Manufacturing

 

Additive Manufacturing (AM) is one of the advanced manufacturing method. Additive manufacturing method includes a number of technologies. Various types of additive manufacturing or 3D printing has been discussed previously, if you want to read it, pleas click here. In this article we will study about the materials used in additive manufacturing or 3D Printing.


 

Primary materials used in additive manufacturing are:

  1. Polymers
  2. Metals
  3. Ceramics

Material used in Additive Manufacturing.

Nowadays, composite  is also being used in 3D printing. The composite is a material, which is made up of two different materials. The composite used in 3D printing  may be of:

  1.  Composite of Metal and Polymer
  2. Composite of Polymer and Ceramics
  3. Composite of Metal and Ceramics

Polymers

Polymer is most popular in 3D printing, because it is cheap and technology which used polymer as feed material for 3D printing, are also easily available and simple in design. Fused Deposition Modelling (FDM) is one of those technology. It is also called as Fused Filament Fabrication (FFF). You can buy a 3D printer based on FFF technology starting from ₹ 15,000 - ₹ 20,000. 

 A few examples of polymers used in this technology are:

  1. Polylectic Acid (PLA)
  2. Acrylonitrile Butadiene Styrene (ABS)
  3. Poly Carbonate (PC)
  4. High Impact Polystyrene (HIPS)
  5. Polyethylene Terephthalate (PET)
  6. Polyethylene Terephthalate - glycol-modified (PET-G)
  7. Nylon 


 

Labels:

Comments

Post a Comment

Popular posts from this blog

Making LED Fade in and out using Arduino

Hi Friends!!!!!! We have learnt how to blink LED with the help of Arduino, that's great! But now we will learn how to make a LED fade in and out gradually using a function in arduino : analogWrite(); Let's have a look on components, which we are going to need ahead. COMPONENT NEED -  Breadboard (1) Arduino (1) Jumper Wires LED 5mm (1) Resistor1K ohm (1) Power Source 5V (1) Now we place these components to make a proper circuit. CIRCUIT PREPRATION - Black wire - GND Red Wire   - +5V Take the breadboard and arduino. Connect the GND from arduino to -Ve terminal on breadboard. Similarly +5V to the +Ve terminal on breadboard.   Now place the LED on breadboard. Connect the positive terminal of LED to the 9th pin of arduino. Why we connecting the LED to the pin 9 of arduino ???? Because pin 9 of arduino can be used for PWM purpose. We needed PWM (Pulse Width Modulation) because Arduino board can only give digital signal (HI...
Post a Comment
Read more

Blinking of LED Using Arduino UNO

Hi !!!! Here we are going to learn very very simple use of Arduino, that is blinking of a LED. Here we will do simplest project using Arduino. So, here we go.... COMPONENTS REQUIRED - Bread Board Arduino UNO Jumper Wires Power Source (5V) / Battery Resistor (1K) CIRCUIT PREPA RATION - Take bread board and Arduino. Connect the +5V from Arduino to the +Ve line on Bread Board and GROUND from Arduino to -Ve line on bread board. Red Wire     : +5 V Black Wire  : GROUND     Now put a LED on bread board. Connect the Anode (+ / Longer terminal) of led to the pin 13 of Arduino. Connect Cathode (- / Shorter terminal)  to 1K ohm resistor and connect another terminal of resistor to the GND on breadboard.   Now our circuit is ready to work.  Our next aim is to build the code. Let's make our code. CODE -     To download the complete code -  CLICK HERE -----------------------------...
Post a Comment
Read more

Introduction to Additive manufacturing and demonstration of part fabrication

  Introduction : Additive Manufacturing  Additive manufacturing uses data computer-aided-design (CAD) software or 3D object scanners to direct hardware to deposit material, layer upon layer, in precise geometric shapes. As its name implies, additive manufacturing adds material to create an object. By contrast, when you create an object by traditional means, it is often necessary to remove material through milling, machining, carving, shaping or other means.  Although the terms "3D printing" and "rapid prototyping" are casually used to discuss additive manufacturing, each process is actually a subset of additive manufacturing.   Additive Manufacturing Processes Binder Jetting   T his technique uses a 3d printing style head moving on x, y and z axes to deposit alternating layers of powdered material and a liquid binder as an adhesive. Directed Energy Deposition  Direct energy deposition additive manufacturing can be used with a wide variety of materials in...
Post a Comment
Read more