Skip to main content

Posts

Featured Post

Kerala's First 3D Printed Building

Created as a showcase project, AMAZE-28, the single-room summer house, was successfully constructed within 28 days on the grounds of the Kerala State Nirmithi Kendra. The 3D-printed building at the Kerala State Nirmithi Kendra in Thiruvananthapuram. (Photo: Shekunj)  The inauguration of Kerala's inaugural 3D-printed structure, a 380-square-foot single-room summer house, is scheduled to take place on October 10 at the Kerala State Nirmithi Kendra (Kesnik) campus located in PTP Nagar, Thiruvananthapuram.  Conceived as a showcase initiative, the summer house named AMAZE-28 was successfully finished within a mere 28 days. This impressive project was executed by Tvasta, a construction technology startup based in Chennai, founded by alumni of IIT-Madras, who have entered into a memorandum of understanding (MoU) with Kesnik.  AMAZE-28 is perched upon a concrete foundation atop a gentle elevation within the Kesnik campus. Febi Varghese, the Director and Chief Executive Officer of Kesnik, p
Post a Comment
Read more

Making LED Fade in and out using Arduino

Hi Friends!!!!!! We have learnt how to blink LED with the help of Arduino, that's great! But now we will learn how to make a LED fade in and out gradually using a function in arduino : analogWrite(); Let's have a look on components, which we are going to need ahead. COMPONENT NEED -  Breadboard (1) Arduino (1) Jumper Wires LED 5mm (1) Resistor1K ohm (1) Power Source 5V (1) Now we place these components to make a proper circuit. CIRCUIT PREPRATION - Black wire - GND Red Wire   - +5V Take the breadboard and arduino. Connect the GND from arduino to -Ve terminal on breadboard. Similarly +5V to the +Ve terminal on breadboard.   Now place the LED on breadboard. Connect the positive terminal of LED to the 9th pin of arduino. Why we connecting the LED to the pin 9 of arduino ???? Because pin 9 of arduino can be used for PWM purpose. We needed PWM (Pulse Width Modulation) because Arduino board can only give digital signal (HIGH or
Post a Comment
Read more

Blinking of LED Using Arduino UNO

Hi !!!! Here we are going to learn very very simple use of Arduino, that is blinking of a LED. Here we will do simplest project using Arduino. So, here we go.... COMPONENTS REQUIRED - Bread Board Arduino UNO Jumper Wires Power Source (5V) / Battery Resistor (1K) CIRCUIT PREPA RATION - Take bread board and Arduino. Connect the +5V from Arduino to the +Ve line on Bread Board and GROUND from Arduino to -Ve line on bread board. Red Wire     : +5 V Black Wire  : GROUND     Now put a LED on bread board. Connect the Anode (+ / Longer terminal) of led to the pin 13 of Arduino. Connect Cathode (- / Shorter terminal)  to 1K ohm resistor and connect another terminal of resistor to the GND on breadboard.   Now our circuit is ready to work.  Our next aim is to build the code. Let's make our code. CODE -     To download the complete code -  CLICK HERE ------------------------------------------------------------------------------------
Post a Comment
Read more

Hand Gesture Controlled Robot

INTRODUCTION Here we are going to make a robot, which will move according to movement of our hand. Here we used accelerometer to sense the movement of hand and RF module for the communication purpose.   Robot will move in following ma nner :           Hand Tilt in                               Robot Motion  Forward  Direction      -                Forward  Backward Direction    -                Backward  Left Direction              -                Left Turn  Right Direction            -                Right Turn    FLOW DIAGRAM COMPONENTS USED   Arduino UNO  RF Module ( Transmitter and Receiver)  HT12E and HT12D  LM324  L293D  Accelerometer  (ADXL335)  BO Motors (2)  750K and 1M ohm resistors  Robot chessis  Castor wheel (1)  Jumper Wires VIDEO OF WORKING ROBOT
Post a Comment
Read more